laser etcher alternative - save money!

LASER ENGRAVER KIT
You Can Save Thousands of Dollars by using the Etch-O-Matic over a Laser Engraver Kit when you are Marking, Etching or Engraving Anything Metal.
 


WHY USE A LASER ENGRAVER KIT?

Now YOU can Permanently Mark or Etch Anything Metal with Names, Numbers, Designs or Trademarks In Seconds and Easily do it 
For Less Than ONE CENT PER MARK!

Why pay $25,000 to $100,000 for a Laser Engraver Kit when the Etch-O-Matic
Will easily Make Marks That COMPARE WITH LASER MARKS?

Our Complete Kits Cost as Little as $79.95!

Here is the Easiest to Use, Lowest Cost Commercial Etching
System on the Market Today....And Anyone in your shop can
quickly learn to be an "Expert" in Minutes and make Top Quality
Commercial Grade Marks or Etches on your Products, Tools, Parts 
or Anything Metal In Seconds and the Marks can be either Black
(Which looks like Printing) or Deep Etched down to .003"  and are
Absolutely Permanent.

A Laser Engraver Kit simply can NOT COMPARE in
cost to the Etch-O-Matic Metal Marking System....And you do
Not have to spend time "Training" a Laser Expert to do your marking,
Anyone in your plant can do it Easily in Minutes!

Free StencilsWould You Like To TRY Our Universal Stencils - Absolutely FREE? Just Click The Shopping Cart Link Below & Let Us Know Your Shipping Information.
It's Just That Simple!

Scroll Down To See How The Etch-O-Matic Marking System 
Works And Then Check Out The Great

SPECIAL OFFER

Here Are Examples Of Permanent Electro-Chemical Marking That 
You Can Easily Do In Your Own Shop In Just Seconds!  Simply Create 
Your Own Copy, Design, Logo Or Trademark And Then Put It On Your 
Tools, Parts Or Equipment For Less Than A Penny Per Mark.  It Is Easy, 
Quick, Inexpensive And Professional!  And You Can Do It!

 

tools

Mark Sockets

tools

Marking Metal Tools

Marking Sockets

Marking Gauges

saw blades

Mark Knives

pocket knife

Marking Sawblades

Marking Knives

Marking Adv. Specialties

tools

surgical instruments

Mark Dies

Marking Cutting Tools

Mark Surgical Instruments

Marking Metal Dies

HERE IS HOW ETCH-O-MATIC SAVES YOU
MONEY OVER A LASER ENGRAVER KIT:

MARKING TOOLS IN SECONDS
eom
MARKING WITH GROUND PLATE Simply Lay the Tool or Part on the Ground Plate and Touch ETCH-O-MATIC to it for a Few Brief Seconds and Your Mark is Permanently Etched Into the Surface.

MARKING DRILL BITS
eom
MARKING ROUND SURFACES Drill Bits, Milling Cutters, Tubing, Pipe or nearly anything Round can be Easily Marked by "Rolling"  the Mark on as Shown Above.

DEEP ETCH TOOL MARKING
eom
MAKES DEEP ETCH MARKS ETCH-O- MATIC Marks many Metals as Deep as .003" with Deep Etch Adapter Clip, a Mark that can only be Removed by Grinding a Major Part of the Surface Away.


laser engraver kit alternative

If it is Made of Metal
ETCH-O-MATIC
Can Etch It And Even
Put Your

TRADEMARK
On It In Just Seconds!
 

new laser etching or laser marking alternative
tools

Permanently Marking Metal Tools  
Without Using A Laser Engraver Kit Will Save YOU Time And Money

MARKING METAL SURFACES ETCH-O-MATIC will Etch into the surface of Anything made of Metal, including Tools, Instruments, Equipment or Manufactured Parts, anything that can be Typed, Written, Drawn or Photo Processed on a Special Stencil. This includes Names, Numbers, Designs, Logos, Trademarks or even Your Own Signature. Using an Electro- Chemical principle, the New ETCH-O-MATIC can Etch as Deep as .003" of an Inch in Less than 30 Seconds or Mark the Hardest Tool Steel and Carbides almost Instantly. It marks any Flat or Round Metal Surface down to 1/16" Diameter and any Metal Thickness from Thin Foil up to the Largest Castings easily. Most Marks (which look like Printing or Engraving) take about 3 to 20 Seconds (the Longer Dwell Times are for Deep Etching) and are Permanently Etched into the Tool or Manufactured Part.
 

FAST AND VERY EASY TO USE!

ETCH-O-MATIC is FAST and EASY TO USE. Anyone in Your Organization can become an EXPERT in JUST MINUTES and produce Professional Looking Marks Quickly. In Fact, Etch-O-Matic is by Far the Very Easiest Marking System to Learn that is Available Today!  Also, You will find that ETCH-O-MATIC is not only the Fastest way to make Permanent Marks on Anything Metal, but is by Far the LEAST EXPENSIVE method on the Market Today. Your Marks will Cost just Fractions of a Cent to Produce and You will be Extremely Pleased with the Result.

COMPARES WITH LASER ETCHES

Most Marks will Compare Favorably with Laser Marks on Metal and are Easier and Sometimes Even Faster to Make.  In Fact You have Seen Marks made by Etch-O-Matic hundreds of times before but probably did Not Realize it since the Marks are Used so often in Commerce Today.  If you have ever seen a Feeler Gauge, Drill Bit, Milling Cutter, Saw Blade, Knife Blade, Ball Bearing Race, Carbide Cutter or Thousands of other types of Metal Tools, Parts, Instruments or Equipment then You have probably seen Marks made by Etch-O-Matic.  In fact, we have Marks in a good Percentage of all of the Cars, Trucks, Commercial and Military Aircraft, Submarines, Hospital Surgical Instruments and Implant Devices and we even have Marks in the Nose Cone of the Space Shuttle.  (Yes, NASA called and said that they used an Etch-O-Matic to Mark an Inspection Date and Number in the Nose Cone of the Space Shuttles.)

BASICALLY, ETCH-O-MATIC and the Electro-Chemical Metal Marking System has been Proven Over and Over again during our 36 Years in Business as the Best and Least Expensive Way to Permanently Mark Anything Metal.  

        

OUR LASER ENGRAVER KIT ALTERNATIVE USES DURA-FILM STENCILS
HERE IS AN EXAMPLE OF HOW THEY ARE USED:


Here Is The Quick, Easy And Inexpensive Way To Mark Your Tools, Parts Or Even A Knife.
First Make Your Artwork On Your Computer With Our New Ultra Violet Stencil-Makers.
When Finished It Should Look Like This One.  Or You Can Use Our Regular Die Impressed Stencils Which Are Included In Every Kit By Simply Typing On Them.
(Explained Below)

         laptop      

Next Place The Stencil On Your Tool, Part Or Knife Blade And Use A 
Small Piece Of Scotch Tape To Hold It In Position. (NOTE: You Can Put The 
Stencil Directly On The Etch-O-Matic For Marking Metal, But This Method Is 
Used For Exact Placement On An Item.)

stencil

When Ready Wet The Head Of The Etch-O-Matic With Electrolyte And
Place It On The Stencil.  After Everything Is Lined Up Correctly Just 
Touch The Blade With The Ground Wire (Shown With Alligator Clip)
For A Few Seconds And Your Mark Is Complete.

knife

Here Is Your Mark.  It Is Black On Stainless Steel But You Can Also Makeknife
Deep Etch Marks Down To About .003" And They Can Be "Clear" Or Black.

 

Now You Can See Just How Easy It Is To Put Your Own Mark On
Anything Metal Including Tools, Parts, Instruments Or Even Knives.

 

A QUICK NOTE ON STENCILS

In Each Etch-O-Matic Kit There Is A Package Of  Stencils.  They Are Prepared By Using A Typewriter Or Dot Matrix Printer Like The Sample Shown Below.  This Is Quick, Easy And Cheap As You Can Do It Yourself If You Have A Typewriter.  The Marks Will Look Just Like You "Typed" In Black Letters On Your Parts.  If That Is Good Enough, Then Go This Route.  Otherwise You Can Make Your Own Dura-Film Stencils As Shown Below Or Even Send Us Your Artwork And We Will Make Them For You. 

Contact Us By Email, Fax or Phone For This.


stencils

Sample Of Typewriter Type Stencil That Comes In Each Kit Shown Above.
We Have Typed "SAMPLE MARK" To Show You How It Would Look.


HOW TO MAKE DURA-FILM STENCILS

Here is How You Make Your Dura-Film Stencils In About 3 Minutes.
(NOTE: We Are Using Large Type So It Will Photograph Easily.)

computer

First Make Your Copy On Your Computer.  Here Is A Simple A B C Made Large
To Show In The Photo.  You Can Make Any Line Drawing,  Logo, Trademark
 or Simple Message You Wish.  There Is Not Much Limit Except Photos Are
Difficult And Very Thin Lines Are Hard To Mark.

transparency

Next Print Out Your Copy On A Transparency (Which Comes In The Kit)
And Place The Transparency Copy On A Piece Of Unexposed Dura-Film
Stencil (Which Comes In The Kit) And Finally Place A Glass Plate On Top.

stencil maker

Next Place Tray In The 440 Dura-Film Stencil Maker And Turn On 
Exposure Unit For About 3 Minutes.

developer

Next Remove Stencil And Develop For 30 Seconds To A Minute.
Stencil Is Then Ready To Use To Mark Your Tools, Parts, Knives Or Anything Metal.

saws

Here We Are Marking A Saw Blade Since It Is Large Enough To Make A Good 
Photo.  You Simply Lay The Stencil On The Blade, Wet The Etch-O-Matic Pad 
(On Bottom) With Electrolyte, Then Place The Etch-O-Matic On The Stencil, Ground 
For A Few Seconds And Then Remove And Your Blade Is Permanently Marked.

EXAMPLES OF ETCH-O-MATIC MARKS

ETCH-O-MATIC MAKES FOUR KINDS OF MARKS

Our Most Popular Etch-O-Matic Metal Marking Kits Are Combined BELOW With The New STENCIL MAKERS For
SPECIAL COMBO OFFERS YOU MUST SEE!

NO ONE BEATS THESE PRICES!

THIS WILL REALLY SAVE YOU MONEY OVER
A LASER ENGRAVER KIT!

ETCH-O-MATIC STARTER KIT

Lowest Priced Kit available Anywhere, Yet it Does the Job in Industry, in Plants, Machine Shops and Everywhere Metal Marking is needed.  The Marker Unit is 10 volts, 2 amps and is Excellent for Light Duty Marking of Tools and Parts.  (Transformer is inside marker unit) 

KIT CONTAINS:
ETCH-O-MATIC marker with standard head marking size 7/8" x 13/4", electrical cord, ground plate, 2 oz. Electrolyte solution in plastic bottle, 10 special stencils, neutralizer, deep etching adapter clip and complete instructions. Each kit will make approximately 1,000 marks before refill supplies are needed.

Unit is 110 Volts standard, but is available in 220 volts for $20 more.

Only $79.95 Complete!

starter kit

SUPER ETCH-O-MATIC KIT
HEAVY DUTY... INDUSTRIAL QUALITY
BEST VALUE ON THE MARKET TODAY!

NEW SUPER ETCH-O-MATIC is a Powerful, 15-Volt, 10-Amp, Heavy Duty, Industrial Quality Marking System that can Stand Up to Continuous Duty, Production Line Marking. It can make Fast A.C. Marks, then Change Instantly to Deep Etch Marking Down to .003" Deep. It can make Large Marks 2" x 4" or Larger (with optional purchase of  Medium or Large Grid Kits) for Trademarks or Etch Hard-to-Mark Coatings like Black Oxide Quickly. This is a Solid, "No Frills" Etcher that is Priced $200 to $300 BELOW Similar Kits on the Market Today.

KIT CONTAINS: 1 - 15-volt, 10-amp. marker unit with external transformer; adapter clip for deep etch marking; ground plate; 8-oz. general purpose electrolyte; 8-oz. neutralizer; extra pads; 100 pak special stencils; complete instructions and packed in sturdy plastic carrying case.

Unit is 110 Volts standard, but is available in 220 volts for $20 more.

Only $229.95 Complete!

super kid

SUPER INDUSTRIAL KIT
$400.00 VALUE SAVE $120.00!

THE NEW SUPER ETCH-O-MATIC INDUSTRIAL KIT Combines the Best of Both of the TWO Kits Above and gives You enough Supplies to Mark Almost Any Type of Metal in the Average Plant. It also provides Great Value Because You get the Starter Kit 10-volt / 2-amp Unit Included FREE in the Kit.   Also Included is a Large 2" x 4" Grid that Allows You to Mark Much Larger Areas at the Same Time.   THIS IS REALLY A

SUPER VALUE AT THIS LOW PRICE!

KIT CONTAINS:
1 Super and 1 Regular ETCH-O-MATIC marker along with an adapter clip for deep etch marking, ground plate, 8 oz general purpose and stainless steel electrolyte, two (2) 100 paks stencils, 4 oz. of aluminum, black oxide, and brass, copper & bronze electrolyte, 1 large 2" x 4" grid with stencils and pads to fit, 8 oz. neutralizer, 2 neutralizer powder paks, 1 extra regular grid and complete instructions.

Unit is 110 Volts standard, but is available in 220 volts for $20 more.

Only $329.95 Complete!

stencil kit


 TODAY'S SPECIALS!
Here Are The BEST Deals Available Anywhere!

NO ONE BEATS THESE PRICES SO CLICK THE LASER ENGRAVER KIT LINK
BELOW TO
CHECK THEM OUT AND SAVE THOUSANDS! 

See Specials On OurLaser Engraver Kit Alternatives


If You Still Have Questions Just Call Us At 800-775-0797 During Pacific Coast
 Time
From 8:00 A.M. To 4:30 P.M. And A Real Person Will Talk With You
And Explain Anything You Want To Know.  Or email Us 
At sales@etching-metal.com  Or FAX At 1-360-985-2996

P.O. Box 200 / 500 Wilcox Road
Salkum, WA 98582
 E-Mail: sales@etching-metal.com
Phone: 1.800.775.0797
Fax: 1.360.985.2996